A 3D raised logo can fail before it ever reaches the heat press.

The raised effect may be too low. White ink may become weak or inconsistent. CMYK can shift away from the white structure. Varnish may show visible bands. Thick layers may wrinkle, remain soft inside or become too brittle after curing.

These problems should not all be treated as “printhead problems.”

Most 3D raised-logo printing defects can be traced to four main systems:

White Ink Delivery

درمان UV

Multi-Pass Registration

Varnish Output

The best troubleshooting method is therefore:

Identify the symptom first, isolate the relevant system, and change only one production variable at a time.

Do not immediately increase white passes, UV power or cleaning cycles without first understanding the actual cause.

If you are still learning the complete production sequence, start with چگونه با چاپگر UV DTF لوگوهای سه بعدی بسازیمبشر

Quick Troubleshooting Table

Start with a Controlled Diagnosis

Before changing printer settings, perform a basic inspection.

1. Check the Artwork and RIP Preview

تایید کنید که:

• the structural white mask is correct
• CMYK is positioned correctly
• varnish coverage is intentional
• all production layers have the same scale
• نقشه برداری نقطه/کانال درست است

A production defect cannot be fixed by printer maintenance if the file itself is wrong.

For detailed prepress guidance, see the راهنمای آثار هنری لوگوی سه بعدی: راه اندازی لایه سفید، CMYK و لاک الکلبشر

2. Run a Nozzle Check

Determine whether:

• White is complete
• CMYK channels are complete
• Varnish is complete

Do this before evaluating height or gloss.

3. Identify Which Layer Is Actually Failing

بپرسید:

Is only White affected?

→ investigate white ink delivery.

Is only one CMYK color affected?

→ investigate that color channel.

Are all layers shifted?

→ investigate registration or media feeding.

Is the print correct but the surface finish poor?

→ investigate varnish and curing.

This prevents unnecessary adjustments to unrelated parts of the system.

Problem 1: The 3D Raised Effect Is Too Low

A low raised effect is one of the most common problems in this application.

But the wrong response is:

“Just print more white layers.”

Before increasing the structural build, confirm why the height is low.

There are four major possibilities.

Cause 1: The Structural White Mask Is Wrong

The printer can only build height where the file tells it to print structural white.

If the White Mask:

• misses part of the artwork
• is too small
• contains unintended gaps
• is mapped incorrectly in the RIP

the final badge will have weak or incomplete height.

Compare the White-only RIP preview with the intended raised structure.

If the geometry is wrong, correct the artwork before changing print parameters.

Cause 2: White Nozzles Are Missing

Repeated white printing multiplies the effect of nozzle loss.

A small missing section in a normal underbase may be difficult to notice.

In a multi-layer 3D build, the same missing nozzles can repeat through multiple passes, producing:

• ارتفاع ناهموار
• visible channels
• weak edges
• inconsistent structure

Run a nozzle check before adjusting white pass count.

Cause 3: White Ink Flow Is Too Weak

The printhead may be functioning, but the ink-delivery system may not maintain enough white flow during continuous high-build printing.

Possible signs include:

• the first logo looks good
• later logos become thinner
• white density gradually decreases
• nozzle check deteriorates during long jobs

This points toward ink delivery rather than simply insufficient RIP buildup.

Cause 4: The Build Profile Is Too Conservative

Only after:

• White Mask is correct
• nozzle condition is good
• white ink flow is stable

should you consider whether the structural white build itself needs adjustment.

The correct goal is not maximum thickness.

این است:

Enough stable white buildup to reach the target 3D height while maintaining flexibility and curing stability.

For the underlying height-building principle, see چگونه لایه‌های جوهر سفید جلوه‌های سه بعدی را در چاپ UV DTF ایجاد می‌کنندبشر

Problem 2: White Ink Looks Thin, Gray or Uneven

White ink is more demanding than CMYK because the flexible high-build white system contains a high concentration of pigment and solids.

That is why stable white-ink movement is especially important in 3D raised-logo production.

Check the white ink system in this order.

White Ink Stirring

High-build white ink should remain uniform rather than allowing heavy pigment to settle in the ink container.

If the ink separates:

• the upper portion may become weaker
• pigment concentration may become inconsistent
• print density can change
• sedimentation can increase the risk of flow problems

گردش جوهر سفید

The circulation system keeps ink moving through the white-ink path.

For repeated high-white production, this helps maintain more consistent ink concentration and delivery.

EraSmart پرینتر A2 UV DTF is designed with white-ink stirring and circulation functions to support white-ink stability.

Check for Air in the Ink Line

Visible air bubbles can interrupt ink delivery.

علائم احتمالی عبارتند از:

• random missing white output
• unstable nozzle check
• white output that suddenly weakens
• inconsistent density during long printing jobs

Do not confuse air-related supply instability with a permanently damaged printhead.

Check Whether the Problem Appears Over Time

This distinction is useful.

Weak White from the First Print

بررسی کنید:

• ink condition
• بررسی نازل
• RIP output
• ink delivery

White Starts Strong and Becomes Weak Later

Pay additional attention to:

• sustained ink flow
• گردش خون
• air
• supply restriction

A time-dependent problem often points toward delivery stability.

Problem 3: White Ink Keeps Dropping Nozzles

Repeated nozzle loss does not automatically mean the printhead must be replaced.

Before making that conclusion, check the complete white-ink path.

Possible causes can include:

• ته نشین شدن رنگدانه
• unstable circulation
• air bubbles
• restricted ink flow
• damper or filter restriction
• poor capping condition
• آلودگی
• unsuitable ink condition

A practical diagnostic sequence is:

بررسی نازل

↓

White Ink Condition

↓

Stirring

↓

گردش

↓

Ink Line / Air

↓

Damper / Filter / Supply

↓

Capping & Cleaning

↓

Print Again

Avoid repeatedly performing aggressive cleaning without understanding the actual supply problem.

Excessive cleaning wastes ink and may not solve a circulation or air issue.

Problem 4: Layers Wrinkle or Separate During UV Curing

Thick flexible UV ink does not behave exactly like a thin conventional UV layer.

When high-build white ink is printed repeatedly, the printer must stabilize a much thicker structure.

There are three important curing conditions to understand.

Under-Cured

علائم احتمالی عبارتند از:

• soft surface
• sticky feel
• تغییر شکل
• unstable structure
• weak internal cure

This can happen when the ink receives insufficient effective UV energy for the total deposited thickness.

Balanced Progressive Cure

The ideal process stabilizes the printed layer while allowing the complete structure to cure properly.

The finished result should be:

• structurally stable
• قابل انعطاف
• clearly raised
• properly surfaced
• suitable for downstream cutting and transfer

Over-Aggressive Surface Cure

Another problem can occur when the surface is locked too aggressively while the thick internal structure has not developed correctly.

علائم احتمالی عبارتند از:

• چروک شدن
• internal stress
• brittle surface
• micro-cracking
• جداسازی لایه ها

The correct solution is not to copy one universal UV-lamp percentage.

UV curing depends on the complete combination of:

• جوهر
• layer thickness
• carriage speed
• pass strategy
• LED-UV system
• total build

For this reason, EraSmart recommends using a validated curing profile for the actual 3D ink and film system.

Problem 5: The Surface Feels Sticky

If the finished printed badge remains sticky before heat transfer, stop production.

علل احتمالی عبارتند از:

• incomplete UV curing
• excessive total ink deposition
• incorrect cure profile
• UV lamp output issue
• incompatibility between ink and production settings

Do not assume that a sticky thick print can simply be fixed later during heat pressing.

The UV print itself should first reach a stable condition suitable for contour cutting and handling.

چه چیزی را بررسی کنید

1. Confirm the ink is the correct flexible 3D UV ink system.
2. Check LED-UV operation.
3. Check the production profile.
4. Reduce uncontrolled excessive buildup.
5. Produce a small test badge.
6. Inspect the surface and internal stability again.

Do not continue a batch if curing is clearly unstable.

Problem 6: The Printed Logo Is Too Hard or Cracks When Bent

A dramatic 3D height can look impressive, but maximum height is not automatically the best production setting.

The EraSmart raised-logo workflow is designed around approximately 00.3-1.2 میلی متر of raised structure, depending on the artwork and validated profile.

If the badge becomes too rigid before transfer, investigate:

• excessive white buildup
• excessive total ink thickness
• overly aggressive curing
• incorrect ink system
• excessive varnish
• design areas that are too thick for their size

A good apparel badge needs to balance:

ارتفاع

Visual Definition

انعطاف پذیری

A logo that looks excellent on the film but cracks immediately during a bend test is not a successful textile product.

Problem 7: A White Edge Appears Around the CMYK

A visible white edge can come from two different causes.

These should not be confused.

Cause A: White Mask Is Too Large

If white appears relatively evenly around the design:

suspect the White Mask / choke relationship.

The structural white may extend beyond the visible CMYK artwork.

This is primarily a prepress problem.

Cause B: Registration Is Shifted

If white appears mainly on one side while the opposite side is too close to the color edge:

suspect registration.

علل احتمالی عبارتند از:

• layer positioning
• جنبش رسانه ای
• تراز چاپی
• multi-pass accumulation
• RIP position

This is not solved simply by applying more choke.

قانون تشخیصی ساده

White around most sides

→ check mask size.

White mainly on one side

→ check registration.

For detailed White Mask and choke preparation, see the راهنمای آثار هنری لوگوی سه بعدی برجستهبشر

Problem 8: CMYK Is Shifted from the Raised White Structure

A small positional error can become much more visible in multi-layer 3D printing.

چرا؟

Because the same structural region is printed repeatedly.

Even small deviations can produce:

• stepped edges
• دیواره های جانبی ناهموار
• exposed white
• CMYK offset
• varnish offset

بررسی کنید:

Media Feed Stability

The film should move consistently during repeated printing.

Printhead Alignment

Verify the applicable alignment settings.

RIP Position

Confirm that the White, CMYK and Varnish planes share:

• the same dimensions
• the same origin
• the same scale
• the same orientation

Repeated-Pass Accumulation

Determine whether:

• the first passes look aligned
• later structural passes gradually shift

If the error increases with each pass, the issue may be related to repeated positioning rather than the original artwork alone.

Problem 9: White Halo vs Registration Error

These two symptoms deserve separate diagnosis because they are often confused.

White Halo

The white layer is correctly centered but too large.

Typical appearance:

uniform white outline

Likely area:

White Mask / Choke

Registration Error

The white layer is not centered beneath the CMYK.

Typical appearance:

white visible on one side, color overhanging on another

Likely area:

alignment / feed / positioning

Do not solve a mechanical shift by aggressively shrinking the entire White Mask.

That may hide one edge while creating insufficient support elsewhere.

Problem 10: Varnish Shows Visible Bands

Varnish defects can be especially obvious because reflected light makes surface variation easy to see.

If the surface shows repeated glossy and dull bands, check:

• varnish nozzle condition
• pass pattern
• output consistency
• carriage movement
• curing consistency

First determine whether the banding exists in the varnish output itself or appears only after curing.

Inspect Under Angled Light

A useful inspection method is to tilt the badge under directional light.

Varnish defects often become much easier to identify because the reflected highlight reveals:

• bands
• missed areas
• rough texture
• inconsistent gloss

Problem 11: Some Areas Are Glossy and Others Are Dull

Uneven gloss can have several causes.

Varnish Output Is Inconsistent

Check the varnish nozzle pattern.

UV Curing Is Uneven

The same amount of varnish can appear different when the cure state varies.

Surface Is Contaminated

Dust, oil or debris can interfere with the finishing layer.

Film Is Not Stable or Flat

Surface position can affect print and curing consistency.

Do not immediately increase varnish density until these basic conditions are checked.

Problem 12: Varnish Surface Looks Rough or Grainy

A rough surface may indicate:

• poor varnish atomization/output
• آلودگی
• excessive material deposited in one stage
• curing behavior that does not match the varnish layer
• nozzle instability

Compare the defective area with a known-good sample.

Check whether the roughness:

• follows nozzle direction
• appears randomly
• appears only in high-varnish areas
• appears only after curing

The pattern itself can help identify the system responsible.

Problem 13: Varnish Is Misaligned

If varnish extends beyond the intended artwork or misses part of the logo, determine whether the problem exists in:

the file

یا:

the physical registration

Check the RIP preview first.

If the Varnish Mask is already shifted in software, fix the artwork or channel mapping.

If the preview is correct but the printed result is shifted, inspect registration, feed and alignment.

Problem 14: Banding Appears in White or CMYK

Banding can come from more than one system.

A useful first diagnosis is to ask which channels are affected.

Only White Has Bands

Focus first on:

• white nozzle condition
• white flow
• stirring
• گردش خون
• air
• white supply

Only One CMYK Color Has Bands

Focus on that specific color channel.

All Colors Have the Same Repeating Pattern

Investigate:

• film feeding
• تراز چاپی
• carriage movement
• حالت چاپ
• RIP / pass behavior

Only the Gloss Appears Banded

تمرکز روی:

• لاک زدن
• درمان
• پرداخت سطح

This channel-based approach is faster than treating every banding problem as a generic nozzle issue.

Problem 15: The Logo Looks Good at First but Changes During a Long Batch

This is an especially useful production clue.

If the first badges look good but later badges show:

• lower white height
• weaker white density
• نازل های از دست رفته
• inconsistent varnish
• more banding

investigate systems that change during sustained printing.

These can include:

• ink supply
• white circulation
• pigment stability
• air entering the line
• supply restriction
• ink temperature / operating stability
• accumulating contamination

A defect that grows gradually during production often has a different cause from a defect that appears identically on the very first print.

A Better Troubleshooting Order

When several problems appear at once, use a fixed diagnostic sequence.

Step 1 — Identify the Symptom

Do not start by changing settings.

First describe the problem precisely:

• low height
• missing white
• باندبندی
• white halo
• shifted color
• sticky surface
• ترک خوردن
• poor gloss

Step 2 — Check Artwork and RIP

تایید کنید:

• structural white
• cmyk
• لاک زدن
• layer position
• spot mapping

Step 3 — Run a Nozzle Check

Determine whether every required channel is complete.

Step 4 — Check White Ink Delivery

For white-related problems inspect:

• stirring
• گردش خون
• ink condition
• air
• flow

Step 5 — Check Registration

به دنبال:

• feed stability
• layer shift
• repeated-pass error
• هم ترازی

Step 6 — Check UV Curing

Confirm the thick structure is curing progressively and consistently.

Step 7 — Check Varnish

بازرسی کنید:

• varnish nozzles
• mask
• هم ترازی
• gloss consistency
• درمان

Step 8 — Print a Small Test

Do not restart full production immediately.

Print a controlled sample.

بررسی کنید:

• ارتفاع
• ثبت نام
• انعطاف پذیری
• براق
• درمان

Then change only one additional variable if necessary.

Do Not Change Multiple Variables at Once

Imagine a low-height badge.

If you simultaneously:

• increase white passes
• increase white ink density
• increase UV power
• slow the print mode

and the result improves, you still do not know what solved the original problem.

Worse, one change may have solved the problem while another created unnecessary rigidity.

A better production-development process is:

Change One Variable

↓

چاپ

↓

بازرسی کنید

↓

Record Result

↓

Keep or Revert

This makes the final production profile repeatable.

When Is the Problem No Longer a Printing Problem?

This guide focuses on problems that exist before the badge is transferred to the garment.

If the printed badge:

• has correct height
• is properly cured
• has clean registration
• has good varnish
• remains flexible
• passes pre-transfer inspection

but problems occur only after heat pressing, move to the heat-transfer workflow.

مثالها عبارتند از:

• logo edges lifting from the garment
• hoodie transfer bonding unevenly
• carrier peeling incorrectly
• مهاجرت رنگ پلی استر
• press marks
• لباس سوزان
• cap pressure problems

Those issues are covered in the راهنمای انتقال حرارت لوگوی سه بعدی برای تی شرت، هودی، کلاه و ژاکتبشر

این تمایز مهم است.

Do not keep changing printer settings to solve a problem caused by the heat press.

Recommended Pre-Production Quality Check

Before contour cutting and heat transfer, inspect every new 3D raised-logo profile.

White Structure

بررسی کنید:

• required height
• uniform buildup
• no missing areas
• no severe sidewall defects

cmyk

بررسی کنید:

• رنگ
• جزئیات
• ثبت نام
• no exposed structural white

لاک الود

بررسی کنید:

• intended gloss
• smooth surface
• correct registration
• no visible banding

درمان

بررسی کنید:

• no sticky surface
• no unstable internal structure
• no obvious wrinkling
• reasonable flexibility

تست خم شدن

Gently flex the sample.

به دنبال:

• ترک خوردن
• جداسازی لایه ها
• excessive rigidity

Only after the print itself is stable should the badge move to contour cutting and garment transfer.

Why Printer Configuration Matters for 3D Raised Logos

A 3D raised-logo workflow places different demands on a UV printer than a simple thin-layer decorative print.

The production system needs to support:

• independent high-build white output
• CMYK انعطاف پذیر
• لاک زدن
• چاپ ساختاری مکرر
• درمان LED-UV کنترل شده
• stable white-ink stirring and circulation

EraSmart پرینتر A2 UV DTF can be configured as the printing platform for this application when paired with the appropriate flexible UV ink, TPU film and production workflow.

For the broader application system, see چاپ لوگوی سه بعدی با فناوری UV DTFبشر

Final Troubleshooting Checklist

Before changing the structural white profile, confirm:

اثر هنری

• White Mask correct
• CMYK correct
• Varnish Mask correct
• layers registered
• RIP mapping verified

چاپ کردن

• White nozzle check complete
• CMYK nozzle check complete
• varnish nozzle check complete

سیستم جوهر سفید

• ink properly mixed
• stirring operating
• circulation operating
• no obvious air in line
• stable flow during continuous printing

Mechanical / Feed

• film feeding consistently
• print alignment correct
• repeated passes remain registered

درمان UV

• surface not sticky
• structure stable
• no obvious wrinkling
• no excessive brittleness

لاک الود

• no banding
• gloss consistent
• mask correct
• registration correct

Only then should you increase or reduce the structural build.

غذای آماده نهایی

3D raised-logo troubleshooting becomes much easier when every defect is assigned to the correct system.

به یاد داشته باشید:

Low Height does not always mean too few white passes.

It can also mean:

• wrong White Mask
• نازل های از دست رفته
• unstable white flow

A White Edge does not always mean insufficient choke.

ممکن است این باشد:

• mask size
• ثبت نام

Wrinkling does not always mean too little curing.

The thick structure may also be experiencing an unsuitable curing balance.

Poor Gloss does not always mean more varnish is required.

It may come from:

• nozzles
• هم ترازی
• درمان
• آلودگی

The most reliable method is:

Diagnose → isolate → test → change one variable → verify again.

For the full production workflow, continue with چگونه با چاپگر UV DTF لوگوهای سه بعدی بسازیمبشر

For white height building, read چگونه لایه‌های جوهر سفید جلوه‌های سه بعدی را در چاپ UV DTF ایجاد می‌کنندبشر

For White / CMYK / Varnish file preparation, see the راهنمای آثار هنری لوگوی سه بعدی برجستهبشر

And if the print is good but the transferred garment fails, use the راهنمای انتقال حرارت لوگوی سه بعدیبشر

سوالات متداول

Why is my 3D raised logo too flat?

Do not immediately add more white passes. First check the structural White Mask, white nozzle condition and white ink delivery. If those are stable, then evaluate the structural build profile.

Why does my white ink become weak during long printing jobs?

Possible causes include pigment instability, poor circulation, air in the ink line or restricted white ink delivery. Compare the nozzle check before and after sustained printing.

Why does white ink need stirring and circulation?

High-build flexible white ink contains a high concentration of pigment and solids. Stirring and circulation help maintain uniform ink concentration and reduce settling-related instability.

Why do I see a white outline around my logo?

If the white outline is visible relatively evenly around the logo, the White Mask may be too large. If white is mainly visible on one side, investigate registration and feed stability.

Why is my CMYK shifted away from the raised white structure?

Check media feeding, print alignment, RIP positioning and repeated-pass registration. Small positioning errors become more obvious when multiple structural layers are stacked.

Why does the thick UV ink wrinkle?

Possible causes include excessive material buildup or a curing strategy that does not match the thick flexible ink structure. Avoid changing UV energy blindly; validate the complete ink, pass and curing profile.

Why does the printed logo crack when I bend it?

The badge may be excessively thick, overly rigid, improperly cured or produced with an unsuitable ink system. The target is controlled height plus flexibility, not maximum thickness.

Why does my varnish have visible lines?

Check varnish nozzles, output consistency, pass pattern, registration and UV curing. Determine whether the bands are printed into the varnish or appear mainly after curing.

Why is part of the logo glossy and another part dull?

Possible causes include inconsistent varnish output, uneven curing, contamination or surface instability. Check the Varnish Mask and nozzle condition before simply increasing varnish.

Should I increase UV power if the surface is sticky?

Not automatically. A sticky surface indicates that the curing system and total ink build need to be checked. UV power, carriage speed, layer thickness and ink system all interact.

When should I stop troubleshooting the printer and check the heat press?

If the badge has correct height, registration, gloss, curing and flexibility before transfer but fails only after application to the garment, the problem is likely in the heat-transfer stage rather than the printing stage.

Can the same troubleshooting settings be used for every 3D logo?

No. Logo geometry, total build, ink, film, print mode and target height can change the optimal production profile. Establish and record validated settings for each major product type.